Condition: 100% Brand NewItem Type: Sauna Sprayer ControllerMaterial: Metal ABSInductive Switch Voltage: DC12VSolenoid Valve Voltage: AC12VWorking Voltage: AC220VWater Spray Time: 0.1~99sWater Spray Interval Time: 1~990sCycles of Water Spray: 1~30 TimesInstallation Method: Wall mounting or standard rail mountingControl Switch Size: Approx. 68 x 68 mm / 2.7 x 2.7 inController Size: Approx. 68 x 68 x 115 mm / 2.7 x 2.7 x 4.5 inElbow Tube Size: Approx. 25 x 2.2 cm / 9.8 x 0.9 inSprinkler Head Size: Approx. 90 x 30 mm / 3.5 x 1.2 inInlet Valve Size: Approx. 90 x 55 mm/3.5 x 2.2 inWeight: Approx. 987g / 34.8ozInstructions:1. Wiring according to the wiring diagram. Requirement: Connect the power supply and solenoid valve with a national standard multi-strand wire induction switch of not less than 1.5mm2 and connect with 0.5mm2 multi-strand high-temperature wires. The terminal must be added with a terminal or tinned.2. Power-on: Make sure the wiring is correct after power-on. The number on the panel shows the water spray time after power-on.3. Setting: It can be set after the initial power-on self-test. Directly press the and - keys to directly set the water spray time. Long press the and - keys at the same time Compatible for 5 seconds to enter the interval setting. Press the or - key to modify the water spray interval time, and then press the and - keys simultaneously Compatible for 5 seconds to change the number of spray cycles, press the or - key to modify the number of cycles. If the button is not pressed after 3 seconds, the machine will automatically save the newly modified number. (Note: When the machine is perCompatible forming water spraying, pressing the setting button is invalid)4. Sensor head connection: usually only one sensor head is used, directly connect between Vand IN0. If you need to connect two sensor heads, connect the same color wires of the two sensor heads in parallel and connect them between Vand IN1. (All red wires are connected to the Vterminal). If it is a switch, connect the switch directly to the Vand IN2 terminal.5. Solenoid valve installation: When installing the solenoid valve, you need to leave a water storage elbow tube between the sprinkler and the solenoid valve. Keep a little water in the pipeline to isolate the high temperature transmitted from the sauna to avoid burning the solenoid valve.6. Malfunction check: The water from the solenoid valve is not stopped, it may be that the inlet and outlet of the solenoid valve may be reversed, which needs to be replaced.Note:1. When installing the solenoid valve, please note that the direction of the arrow on the valve body is the same as the direction of the water flowing. Use hoses to connect to water pipes to minimize stress.2. It is best to add a valve in front of the solenoid valve to adjust the water volume and maintenance.3. The connecting pipe between the solenoid valve and the sauna stove should retain a section of upward pipe to ensure that there is a section of water behind the solenoid valve to protect the solenoid valve from being burned by the high temperature transmitted from the sauna.4. Compatible for multiple panel switches, please connect them between Vand SW (between 6# and 5#). The panel switches can be used in parallel, generally not more than 5 at most.5. Compatible for the water spray equipment equipped with a sensor, when installing a sensor head, the wiring is between V and K1 (between 6# and 4#). If two sensor heads are installed, firstly connect the two wires of the same color in parallel on the two sensor heads when wiring. If there are more sensors, they can be connected between Vand K2 (between 6# and 3#).6. Regardless of the sensor head or the switch, all the red wires are connected to V(6#). If you accidentally connect it incorrectly, it does not matter, as long as it is replaced, it will not damage the switch and the sensor head.7. The sensor should be installed in a relatively low temperature location to avoid the effect of high temperature on internal components and make the sensor fail.8. Time adjustment: The maximum spraying time is 3 seconds. Toggle the switch up to reduce the time. Each time is reduced by 0.5 seconds. Generally, do not adjust.9. Troubleshooting: The solenoid valve is always out of water: the inlet and outlet of the solenoid valve may be reversed and need to be replaced. Install in the direction of the arrow, or there may be a Compatible foreign body blocking the solenoid valve. The solenoid valve does not produce water: after power on, look at the right indicator on the controller. If it is always on, it may be that the panel switch is not installed properly, or it may be that the panel switch is not functioning at all, it may be a wiring error.