Description
Conditon: 100% Brand New
Item Type: Transistor Tester
Material: Plastic
Color: As Pictures Shown
Battery(Not Included): 9V Cascade Battery
Manual:
1. Use for ATmega8, for ATmega168 or for ATmega328 microcontrollers.
2. 2x16 character LCD display results.
3. One-key operation, automatic power off.
4. The shutdown current is 20nA, which supports battery operation.
5. The low-cost version does not require a oscillator and supports automatic power-off. for ATmega168 or for ATmega328 with 1.05k version software uses sleep mode to reduce power consumption when there is no measurement.
6. Automatic detection of PNP and NPN bipolar transistors, N, P-channel MOSFET, JFET, diode, double diode, thyristor thyristor.
7. Automatically detect the pin layout.
8. Measure the current amplification factor of the bipolar transistor and the threshold voltage of the emitter junction.
9. Darlington transistors can be identified by high threshold voltage and high current amplification factor.
10. Detection of protection diodes for bipolar transistors and MOSFETs.
11. Measure the threshold voltage and gate capacitance of the MOSFET.
12. Support the measurement and signal display of two resistances, the upper four digits and unit display. Both ends of the displayed resistance signal are the connected tester probe numbers (1-3). So the potentiometer can also be measured. If the potentiometer is adjusted to one end of it, the tester cannot distinguish the middle and both ends of the pin.
13. The resolution of resistance measurement is 0.1 ohm, and the high measurement value is 50M ohm.
14. A capacitor can be detected and measured. The upper four digits and unit display. The value can be from 25pf (8MHz clock, 50pF@1MHz clock) to 100mF. The resolution can get to 1 pF (@ 8MHz clock).
15. It can be used to measure the equivalent series resistance (ESR) capacitance value of capacitors above 2UF. The resolution is 0.01 ohms and two-digit values are displayed. This function requires at least 16K flash for ATMEGA (for ATmega168 or for ATmega328).
16. Show signs of the correct direction for the two diodes. In addition, the forward pressure drop is displayed.
17. The LED is detected as a diode, and the forward voltage drop is much higher than normal. The double LED is detected as a double diode.
18. Zener diode can be detected if the reverse breakdown voltage is lower than 4.5V. This will appear as two diodes and can just be determined by voltage. The signal of the probe surrounding the diode is the same, in this case, you can identify the true anode of the diode by the threshold voltage near 700mV!
19. Measure the reverse capacitance of a single diode. Bipolar transistors can also be measured if you connect the base and collector or emitter.
20. Only one measurement is needed to find out the connection of the full bridge.
21. Capacitors with values below 25pf are usually not detected, but they can be connected in parallel with a diode or at least 25pf capacitors in parallel. In this case, you must subtract the part of the parallel capacitance value.
22. Resistance below 2100 ohms will measure inductance, if your for ATMEGA has at least 16K flash memory. The range will exceed 20H from 0:01mH, but the accuracy is not good. The measurement results Only show a single component connection.
23. The test time is about two seconds, Only capacitance and inductance measurements will take a long time.
24. The software can set the number of measurements before the power is automatically turned off.
25. Built-in self-checking function and optional 50Hz signal to check the clock frequency accuracy and waiting for calling (for ATmega168 and for ATmega328).
26. Optional equipment calibration port output internal resistance and 0-offset self-check capability measurement (for ATmega168 and for ATmega328). Need a 100nF to 20uF capacitor connected between pin 1 and pin 3 to compensate the offset voltage of the analog comparator. This can reduce the measurement error of capacitors above 40uF. The internal correction voltage reference voltage with the same capacitor was found to adjust the gain of the internal reference measurement ADC.
If the test current exceeds the holding current, the thyristor and triac can be detected. However, some semiconductor thyristors and triacs have higher trigger currents than the tester can provide. The available test current is Only about 6mA!
-
Fruugo ID:
321527713-713416382
-
EAN:
1277520950576
Product Safety Information
Please see the product safety information specific to this product outlined below
The following information is provided by the independent third-party retailer selling this product.
Safety Warnings:
Do not let your children touch this product alone to avoid swallowing or other injuries.
Delivery & Returns
Dispatched within 3 days
Shipping from China.
We do our best to ensure that the products that you order are delivered to you in full and according to your specifications. However, should you receive an incomplete order, or items different from the ones you ordered, or there is some other reason why you are not satisfied with the order, you may return the order, or any products included in the order, and receive a full refund for the items. View full return policy