LED Program Card for RC Rock Crawler ESC Waterproof Brushless Controller Accessory

Surpass Hobby ROCKET LED Program Card for Rock Crawler Gecko Series MINI 18 30A ESC Brushless Waterproof Electronic Speed Controller RC Car Vehicle PartsPrecise Details: Brand: Surpass Hobby Item Name: Rocket LED Program Card Product Size: 70 x 43 x 13 mm Bag Size: 90 x 80 x 85 mm Net Weight: 24 g Gross Weight: 28 g Power Supply Mode: ESC BEC Compatible ESC: Rock Crawler Gecko Series MINI 18 30A ESC Brushless Waterproof Electronic Speed Controller Instructions: 1. Connect BEC wires with the receiver. 2. Connect motor wires with ESC. 3. Turn on the transmitter. 4. Connect battery pack with ESC, then switch on the ESC. 5. When the connection of motor and battery is finished, the motor emits a “Beep-Beep” tone. 6. When the throttle stick is in the neutral position, the motor re-emits a “Beep-Beep” tone. 7. The ESC is now operational. Troubleshooting: 1. If the motor does not work and emits no sound after power on, check the connections between the battery pack and motor. 2. If the LED flashes after power on, check the battery pack voltage, which should be between 5V and 13V. 3. If the motor emits only a “Beep-Beep” tone, check all connections: BEC wires, transmitter and receiver, throttle signal wires, etc. Check the transmitter TH.TRIM and adjust until the motor re-emits the “Beep-Beep” tone. 4. If the car cannot accelerate, check if the battery voltage is too low or if the ESC temperature is too high. Replace the battery if voltage is low. If ESC temperature is high, check all connections. If connections are secure, adjust the EPA button on the remote control. 5. If the car stops suddenly during operation, check motor connections and any obstructions. 6. If the car runs in the opposite direction while the transmitter is functioning correctly, swap any two motor wires between the ESC and motor. Program Card Settings: 1. Low Voltage Cut-Off: This function prevents lithium battery packs from over-discharging. When using lithium batteries, set an appropriate low-voltage protection level. WARNING: Never use the default setting “Disable” with lithium batteries. Options: 3.1V Slow, 2.9V Slow, 2.7V Slow, Disable, 3.4V Slow, 3.1V Stop, 2.9V Stop, 2.7V Stop, 3.4V Stop (Default: 3.1V Slow). 2. Start Modes (Punch): Level 3, Level 1, Level 6, Level 2, Level 4, Level 5 (Default: Level 3). 3. Maximum Brake Force: 50%, 25%, 75%, 100%, Disable (Default: 50%). 4. Maximum Reverse Force: 25%, 50%, 75%, 100% (Default: 25%). 5. Neutral Range: 9% (Narrow), 6% (Normal), 12% (Wide) (Default: 9%). 6. Motor Overheat Protection: 120°C Stop, 135°C Stop, 150°C Stop, 120°C Slow, 135°C Slow, 150°C Slow, Disable (Default: 120°C Stop). 7. ESC Overheat Protection: 105°C Stop, 95°C Stop, Disable (Default: 105°C Stop). 8. Running Mode: Fwd/Rev/Br, Fwd/Br, Fwd/Rev (Default: Fwd/Rev/Br) (Fwd = Forward, Brk = Brake, Rev = Reverse). 9. Drag Brake Force: 0%, 5%, 10%, 20%, 30% (Default: 0%). Programming Method: 1. Connect BEC wires to the program card, then turn on the ESC. 2. The program card displays ITEM numbers from 1 to 15 with corresponding VALUE settings. 3. Press the "ITEM" button to select different programs. 4. Press the "VALUE" button to select the desired value for the current program. 5. Press the "OK" button to confirm the selection. 6. Press the "RESET" button to restore factory settings. Package Included: 1 x Rocket LED Program Card